Products

Product Details Sold per ft. FULL ROLL OF THIS MATERIAL IS 50FT LONG Specs Width 36 in. Thickness .125" +/-.020 Where Used CHALLENGER® III...

Description The parts present sensor determines whether a garment is on the print pallet before the machine prints. If no garment is present, t...

Specs Width 2.00" Hight 4.00" Legth 96.00" Notes #6 Density Bevel Cut Encapsulated w/Glass

Additional information Weight 1.343 lbs PLC PLC 24 Port LP2 LP3 & XL, PLC 36 Port LP4 & XL, PLC MINI LP1

Description The plug fitting is present in the manifolds of some machines.   Additional information Weight 0.0133 lbs

Description The power cable comes assembled with a power inlet and is pre-stripped on the other end. They are sold per piece.   Additional inform...

Description All Pallets are 8 inches long, please choose the width you need. The LP1 uses 5 pallets, the LP2 and LP3 use 8 pallets, and the LP4 u...

Description All Pallets are 16 inches long, please choose the width you need.   Additional information XL Pallet LPXL 13.25" W x 16" L, Slee...

Specs Motor HP 7.5 HP Voltage 208/230/460V 60Hz Note 5.6 Gpm, 3500 Psi, 1450 Rpm

Specs Type Air Operated Double Diaphragm Flow 11 GPM Note 1/2" FNTP Inlet, 1/2" FNPT Outlet, Polypropylene Body Material

Replacement part number for 3027263 Sold as a complete Assembly

Specs Type Angle Type of Gears Worm Ratio 40:1 Output Type Hollow Bore & Flange RH Output Diameter 1" Input Type Hollow Bor...

Specs Type Offset In-Line Type of Gears Helical Ratio 72.2:1 Output Type Output Shaft (Single) Output Diameter 40 mm Input Type Clampi...

Description The registration system latches onto the registration bearing block to hold the print pallets in the correct position. They are not...

RIGHT HAND REAR MICRO SUB ASSEMBLY

Specs Type Female Thread Direction Right Hand Thread Size 5/16-24 Inside Diameter 0.313" Ball With 0.437" Base to Center 1.375" Body...

Product Details Sold per Inch Specs Description Rubber Seal Width 0.75" Length Sold Per Inch Thickness 0.50" Notes Used for Exposure Uni...

Description The frame holder bracket holds the frame into the print head.   Additional information Weight 0.394 lbs

Description Screen Clamps Knob is for the LP and LPXL Series. The frame attach screw secures the frame to the frame holders. There are four on eac...

Specs Thickness 0.125" Width 1.00 in. Temperature Rating 500F Material Silicone Sponge

Sold by the Inch

Product Details Sold per in. Pls. provide the serial number of the equipment this is needed for. Specs Type Edge Seal Width 0.94 in. Note ...

Specs Motion Type Static Type O-ring Round Cross Section Outside Diameter 0.28 in. Inside Diameter 0.15 in. Width 0.07 in. Temperatur...

Specs Head Socket Thread Size 1/4-20 Length 5/16" Point Cup With Nylon Tip Material Steel Finish Black

Specs Type Self-Compensating Length 3.19" Thread Size 1-12 Stroke 0.45"

Description This air fitting is present on the manifold of the machines. There are several different sizes of this type of fitting, so make sur...

Description This air fitting is present on the manifold of the machines. There are several different sizes of this type of fitting, so make sure ...

Specs Component Type Slide Block Material Type Steel Width of Block 63 mm Length of Block 79 mm Contamination Protection End, Side, &...

Description The air solenoid attaches to the manifold and supplies the various cylinders in the machine with air pressure. The LP-1 uses 2, the LP...

Specs Type Hand Retractable Thread Size 1/2-13 Thread Length 0.650" Where Used  

Specs Type Hand Retractable Material Steel Thread Size 1/2-13 Thread Length 0.875" Where Used CHALLENGER® II & II OS Automatic Scr...